Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
What is a characteristic of an SSID in wireless networks?
- A. allows easy file sharing between endpoints
- B. provides protection against spyware
- C. associates a name to a wireless network
- D. eliminates network piggybacking
Which cable type must be used when connecting two like devices together using these criteria?
• Pins 1 to 3 and 2 to 6 are required.
• Auto detection MDI-X is unavailable.
- A. straight-through
- B. console
- C. crossover
- D. rollover
SIMULATION
–
Guidelines
–
This is a lab item in which tasks will be performed on virtual devices.
• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab doses and cannot be reopened.
Topology
Tasks
–
All physical cabling is in place and verified. Switch SW-1 is pre-configured and inaccessible. SW-2 and SW-3 ports must be configured and operational to complete the configuration.
1. Configure SW-2 and SW-3 ports E0/0 to use the industry standard encapsulation method for trunking and only tag VLAN 10
2. Configure SW-2 and SW-3 ports E0/0 to send and receive untagged traffic over VLAN 11
3. Configure SW-2 and SW-3 ports E0/2 and E0/3 to use the industry standard encapsulation method for trunking and tag all VLANS
4. Configure SW-2 and SW-3 ports E0/2 and E0/3 for link aggregation using the industry standard protocol with the following requirements:
– SW-2 ports must not initiate the negotiation for the aggregation protocol
– SW-3 ports must immediately negotiate the aggregation protocol
– Use the designated number assignment
Answer:
DRAG DROP
–
Drag and drop the characteristic from the left onto the cable type on the right.
What is a characteristic of a Layer 2 switch?
- A. transfers all frames received to every connected device
- B. offers one collision domain for all connected devices
- C. transmits exclusively at half duplex
- D. supports segmentation using tagging protocols
Question 1006
DRAG DROP
–
Drag and drop the IPv6 address from the left onto the type on the right.
Refer to the exhibit. The IPv6 address for the LAN segment on router R1 must be configured using the EUI-64 format. When configured which ipv6 address is produced by the router?
- A. 2001:db8:3bb8:3bb1:C810:B3FF:FF8B:1
- B. 2001:db8:3bb8:3bb1:C001:3BFE:FF81:1
- C. 2001:db8:3bb8:3bb4:6363:93FF:EF66:1
- D. 2001:db8:3bb8:3bb1:C801:B3FF:FEB8:1
Question 1008
PC1 tries to send traffic to newly installed PC2. The PC2 MAC address is not listed in the MAC address table of the switch, so the switch sends the packet to all ports in the same VLAN. Which switching concept does this describe?
- A. frame flooding
- B. MAC address table
- C. spanning-tree protocol
- D. MAC address aging
Refer to the exhibit. What is the cause of the issue?
- A. shutdown command
- B. wrong cable type
- C. STP
- D. port security
Which is a fact related to FTP?
- A. It uses two separate connections for control and data traffic.
- B. It uses block numbers to identify and mitigate data-transfer errors.
- C. It always operates without user authentication.
- D. It relies on the well-known UDP port 69.