Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
What must be considered when using 802.11a?
- A. It is chosen over 802.11b when a lower-cost solution is necessary
- B. It is susceptible to interference from 2.4 GHz devices such as microwave ovens
- C. It is compatible with 802.11b- and 802 11g-compliant wireless devices
- D. It is used in place of 802.11b/g when many nonoverlapping channels are required
What is the recommended switch load-balancing mode for Cisco WLCs?
- A. source-destination IP address
- B. destination IP address
- C. destination MAC address
- D. source-destination MAC address
Which two characteristics are representative of virtual machines (VMs)? (Choose two.)
- A. multiple VMs operate on the same underlying hardware
- B. Each VMs operating system depends on its hypervisor
- C. A VM on a hypervisor is automatically interconnected to other VMs
- D. A VM on an individual hypervisor shares resources equally
- E. Each VM runs independently of any other VM in the same hypervisor
Refer to the exhibit. A network engineer updates the existing configuration on interface fastethernet1/1 switch SW1. It must establish an EtherChannel by using the same group designation with another vendor switch. Which configuration must be performed to complete the process?
- A. interface port-channel 2
channel-group 2 mode desirable - B. interface fastethernet 1/1
channel-group 2 mode on - C. interface fastethernet 1/1
channel-group 2 mode active - D. interface port-channel 2
channel-group 2 mode auto
Refer to the exhibit. A network administrator configures the CPE to provide internet access to the company headquarters. Traffic must be load-balanced via ISP1 and ISP2 to ensure redundancy.
Which two command sets must be configured on the CPE router? (Choose two.)
- A. ip route 0.0.0.0 0.0.0.0 198.51.100.1 255
ip route 0.0.0.0 0.0.0.0 203.0.113.1 255
ip route 128.0.0.0 128.0.0.0 203.0.113.1 - B. ip route 0.0.0.0 128.0.0.0 198.51.100.1
ip route 128.0.0.0 128.0.0.0 203.0.113.1
ip route 0.0.0.0 0.0.0.0 198.51.100.1
ip route 0.0.0.0 0.0.0.0 203.0.113.1 - C. ip route 0.0.0.0 0.0.0.0 198.51.100.1
ip route 0.0.0.0 0.0.0.0 203.0.113.1 - D. ip route 0.0.0.0 128.0.0.0 198.51.100.1
ip route 128.0.0.0 128.0.0.0 203.0.113.1 - E. ip route 0.0.0.0 0.0.0.0 198.51.100.1
ip route 0.0.0.0 0.0.0.0 203.0.113.1 2
Which interface or port on the WLC is the default for in-band device administration and communications between the controller and access points?
- A. console port
- B. management interface
- C. virtual interface
- D. service port
SIMULATION
–
Guidelines
–
This is a lab item in which tasks will be performed on virtual devices
• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window
• All necessary preconfigurations have been applied
• Do not change the enable password or hostname for any device
• Save your configurations to NVRAM before moving to the next item
• Click Next at the bottom of the screen to submit this lab and move to the next question
• When Next is clicked, the lab closes and cannot be reopened
Topology
–
Tasks
–
Connectivity between four routers has been established. IP connectivity must be configured in the order presented to complete the implementation. No dynamic routing protocols are included.
1. Configure static routing using host routes to establish connectivity from router R3 to the router R1 Loopback address using the source IP of 209.165.200.230.
2. Configure an IPv4 default route on router R2 destined for router R4.
3. Configure an IPv6 default router on router R2 destined for router R4.
Answer:
A network administrator wants the syslog server to filter incoming messages into different files based on their importance. Which filtering criteria must be used?
- A. message body
- B. level
- C. facility
- D. process ID
SIMULATION
–
Guidelines
–
This is a lab item in which tasks will be performed on virtual devices
• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window
• All necessary preconfigurations have been applied
• Do not change the enable password or hostname for any device
• Save your configurations to NVRAM before moving to the next item
• Click Next at the bottom of the screen to submit this lab and move to the next question
• When Next is clicked the lab closes and cannot be reopened
Topology
–
Tasks
–
Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured.
1. Configure an LACP EtherChannel and number it as 44; configure it between switches SW1 and SW2 using interfaces Ethemet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends.
2. Configure the EtherChannel as a trunk link.
3. Configure the trunk link with 802.1q tags.
4. Configure VLAN ‘MONITORING’ as the untagged VLAN of the EtherChannel.
Answer:
What are two reasons to configure PortFast on a switch port attached to an end host? (Choose two.)
- A. to block another switch or host from communicating through the port
- B. to enable the port to enter the forwarding state immediately when the host boots up
- C. to prevent the port from participating in Spanning Tree Protocol operations
- D. to protect the operation of the port from topology change processes
- E. to limit the number of MAC addresses learned on the port to 1