Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
What is the primary purpose of a console port on a Cisco WLC?
- A. in-band management via an asynchronous transport
- B. in-band management via an IP transport
- C. out-of-band management via an asynchronous transport
- D. out-of-band management via an IP transport
Refer to the exhibit. After a recent internal security audit, the network administrator decided to block all P2P-capable devices from the selected SSID. Which configuration setting must the administrator apply?
- A. Set the Wi-Fi Direct Client Policy to Not-Allow.
- B. Select a correctly configured Layer 2 ACL.
- C. Set the MFP Client Protection to Required.
- D. Set the P2P Block Action to Drop.
Which default condition must be considered when an encrypted mobility tunnel is used between two Cisco WLCs?
- A. The tunnel uses the IPses protocol for encapsulation.
- B. Control and data traffic encryption are enabled.
- C. The tunnel uses the EoIP protocol to transmit data traffic.
- D. TCP port 443 and UDP 21 are used.
Refer to the exhibit. How must router A be configured so that it only sends Cisco Discovery Protocol information to router C?
- A. #config tRouter A (config)#no cdp run –
Router A (config)#interface gi0/0/1Router A (config-if)#cdp enable – - B. #config tRouter A (config)#cdp run –
Router A (config)#interface gi0/0/0
Router A (config-if)#no cdp enableC.#config t -Router A (config)#cdp run –
Router A (config)#interface gi0/0/1Router A (config-if)#cdp enable – - D. #config tRouter A (config)#cdp run –
Router A (config)#interface gi0/0/0
Router A (config-if)#cdp enable
Refer to the exhibit. The SW1 and SW2 Gi0/0 ports have been preconfigured. An engineer is given these requirements:
• Allow all PCs to communicate with each other at Layer 3.
• Configure untagged traffic to use VLAN 5.
• Disable VLAN 1 from being used.
Which configuration set meets these requirements?
- A. SW1#
interface Gi0/1
switchport mode trunk
switchport trunk allowed vlan 5,7,9,108
switchport trunk native vlan 5interface Gi0/2
switchport mode trunk
switchport trunk allowed vlan 5,7,9,108SW2#
interface Gi0/1
switchport mode access
switchport access vlan 7interface Gi0/7
switchport mode trunk
switchport trunk allowed vlan 7,9,108 - B. SW1#
interface Gi0/1
switchport mode trunk
switchport trunk allowed vlan 5,7,9,108
switchport trunk native vlan 5interface Gi0/2
switchport mode access
switchport trunk allowed vlan 7,9,108SW2#
interface Gi0/1
switchport mode access
no switchport access vlan 1
switchport access vlan 7interface Gi0/7
switchport mode trunk
switchport trunk allowed vlan 7,9,108
switchport trunk native vlan 5 - C. SW#1 –
interface Gi0/1
switchport mode trunk
switchport trunk allowed vlan 5,7,9,108
switchport trunk native vlan 5interface Gi0/2
switchport mode trunk
switchport trunk allowed vlan 5,7,9,108SW2#
interface Gi0/1
switchport mode access
switchport access vlan 7interface Gi0/7
switchport mode trunk
switchport trunk allowed vlan 5,7,9,108
switchport trunk native vlan 5 - D. SW1#
interface Gi0/1
switchport mode trunk
switchport trunk allowed vian 5,7,9,108interface Gi0/2
switchport mode trunk
switchport trunk allowed vlan 7,9,108SW2#
interface Gi0/1
switchport mode trunk
switchport trunk allowed vlan 7interface Gi0/7
switchport mode trunk
switchport trunk allowed vlan 5,7,9,108
Refer to the exhibit. A network engineer configures the CCNA WLAN so that clients must reauthenticate hourly and to limit the number of simultaneous connections to the WLAN to 10. Which two actions complete this configuration? (Choose two.)
- A. Enable the Wi-Fi Direct Clients Policy option
- B. Enable the Enable Session Timeout option and set the value to 3600.
- C. Enable the Client Exclusion option and set the value to 3600.
- D. Set the Maximum Allowed Clients value to 10.
- E. Set the Maximum Allowed Clients Per AP Radio value to 10.
Which switching feature removes unused MAC addresses from the MAC address table, which allows new MAC addresses to be added?
- A. MAC address aging
- B. MAC move
- C. MAC address auto purge
- D. dynamic MAC address learning
Refer to the exhibit. A Cisco WLC administrator is creating a new wireless network with enhanced SSID security. The new network must operate at 2.4 Ghz with 54 Mbps of throughput. Which set of tasks must the administrator perform to complete the configuration?
- A. Uncheck the Broadcast SSID check box and set the Radio Policy to 802.11a/g only.
- B. Check the Broadcast SSID check box and set the Radio Policy to 802.11g only.
- C. Uncheck the Broadcast SSID check box and set the Radio Policy to 802.11g only.
- D. Check the Broadcast SSID check box and set the Radio Policy to 802.11a only.
DRAG DROP
–
Drag and drop the WLAN components from the left onto the correct descriptions on the right.
What is a reason to configure a trunk port that connects to a WLC distribution port?
- A. Provide redundancy if there is a link failure for out-of-band management.
- B. Allow multiple VLANs to be used in the data path.
- C. Permit multiple VLANs to provide out-of-band management.
- D. Eliminate redundancy with a link failure in the data path.