Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
An engineer requires a switch interface to actively attempt to establish a trunk link with a neighbor switch. What command must be configured?
- A. switchport mode trunk
- B. switchport mode dynamic desirable
- C. switchport nonegotiate
- D. switchport mode dynamic auto
Refer to the exhibit. After the election process, what is the root bridge in the HQ LAN?
Switch 1: 0C:E0:38:81:32:58 –
Switch 2: 0C:0E:15:22:1A:61 –
Switch 3: 0C:0E:15:1D:3C:9A –
Switch 4: 0C:E0:19:A1:4D:16 –
- A. Switch 1
- B. Switch 2
- C. Switch 3
- D. Switch 4
An engineer must establish a trunk link between two switches. The neighboring switch is set to trunk or desirable mode. What action should be taken?
- A. configure switchport nonegotiate
- B. configure switchport mode dynamic desirable
- C. configure switchport mode dynamic auto
- D. configure switchport trunk dynamic desirable
Which spanning-tree enhancement avoids the learning and listening states and immediately places ports in the forwarding state?
- A. BPDUfilter
- B. PortFast
- C. Backbonefast
- D. BPDUguard
How does the dynamically-learned MAC address feature function?
- A. The CAM table is empty until ingress traffic arrives at each port
- B. Switches dynamically learn MAC addresses of each connecting CAM table.
- C. The ports are restricted and learn up to a maximum of 10 dynamically-learned addresses
- D. It requires a minimum number of secure MAC addresses to be filled dynamically
When using Rapid PVST+, which command guarantees the switch is always the root bridge for VLAN 200?
- A. spanning-tree vlan 200 priority 614440
- B. spanning-tree vlan 200 priority 0
- C. spanning-tree vlan 200 root primary
- D. spanning-tree vlan 200 priority 38813258
Refer to the exhibit. Which command must be executed for Gi1/1 on SW1 to passively become a trunk port if Gi1/1 on SW2 is configured in desirable or trunk mode?
- A. switchport mode dynamic auto
- B. switchport mode dot1-tunnel
- C. switchport mode dynamic desirable
- D. switchport mode trunk
Refer to the exhibit. The entire contents or the MAC address table are shown. Sales-4 sends a data frame to Sales-1.
What does the switch do as it receives the frame from Sales-4?
- A. Map the Layer 2 MAC address to the Layer 3 IP address and forward the frame.
- B. Insert the source MAC address and port into the forwarding table and forward the frame to Sales-1.
- C. Perform a lookup in the MAC address table and discard the frame due to a missing entry.
- D. Flood the frame out of all ports except on the port where Sales-1 is connected.
Refer to the exhibit. An engineer must configure GigabitEthernet1/1 to accommodate voice and data traffic. Which configuration accomplishes this task?
- A. interface gigabitethernet1/1 switchport mode access switchport access vlan 300 switchport voice vlan 400
- B. interface gigabitethernet1/1 switchport mode trunk switchport trunk vlan 300 switchport trunk vlan 400
- C. interface gigabitethernet1/1 switchport mode access switchport voice vlan 300 switchport access vlan 400
- D. interface gigabitethernet1/1 switchport mode trunk switchport trunk vlan 300 switchport voice vlan 400
An engineer needs to add an old switch back into a network. To prevent the switch from corrupting the VLAN database, with action must be taken?
- A. Add the switch in the VTP domain with a lower revision number.
- B. Add the switch in the VTP domain with a higher revision number.
- C. Add the switch with DTP set to dynamic desirable.
- D. Add the switch with DTP set to desirable.