Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Which switching concept is used to create separate broadcast domains?
- A. STP
- B. VTP
- C. VLAN
- D. CSMA/CD
Refer to the exhibit. Which action must be taken so that neighboring devices rapidly discover switch Cat9300?
- A. Enable portfast on the ports that connect to neighboring devices.
- B. Configure the cdp timer 10 command on switch Cat9300.
- C. Configure the cdp holdtime 10 command on switch Cat9300
- D. Configure the cdp timer 10 command on the neighbors of switch Cat9300
What is a requirement when configuring or removing LAG on a WLC?
- A. The incoming and outgoing ports for traffic flow must be specified if LAG is enabled.
- B. The management interface must be reassigned if LAG is disabled
- C. The controller must be rebooted after enabling or reconfiguring LAG
- D. Multiple untagged interfaces on the same port must be supported
DRAG DROP –
Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.
Select and Place:
Which type of port is used to connect the wired network when an autonomous AP maps two VLANs to its WLANs?
- A. access
- B. LAG
- C. trunk
- D. EtherChannel
A network administrator needs to aggregate 4 ports into a single logical link which must negotiate layer 2 connectivity to ports on another switch. What must be configured when using active mode on both sides of the connection?
- A. LLDP
- B. LACP
- C. Cisco vPC
- D. 802 1q trunks
Refer to the exhibit. An engineer built a new L2 LACP EtherChannel between SW1 and SW2 and executed these show commands to verify the work establish an
LACP port channel?
- A. Change the channel-group mode on SW1 to desirable
- B. Change the channel-group mode on SW1 to active or passive
- C. Change the channel-group mode on SW2 to auto
- D. Configure the interface port-channel 1 command on both swtiches
Refer to the exhibit. For security reasons, automatic neighbor discovery must be disabled on the R5 Gi0/1 interface. These tasks must be completed:
✑ Disable all neighbor discovery methods on R5 interface Gi0/1
✑ Permit neighbor discovery on R5 interface Gi0/2.
✑ Verify there are no dynamically learned neighbors on R5 interface Gi0/1.
✑ Display the IP address of R6’s interface Gi0/2
Which configuration must be used?
- A. R5(config)#int Gi0/1 R5(config-if)#no cdp enable R5(config-if)#exit R5(config)#lldp run R5(config)#no cdp run R5#sh cdp neighbor detail R5#sh lldp neighbor
- B. R5(config)#int Gi0/1 R5(config-if)#no cdp enable R5(config-if)#exit R5(config)#no lldp run R5(config)#cdp run R5#sh cdp neighbor R5#sh lldp neighbor
- C. R5(config)#int Gi0/1 R5(config-if)#no cdp run R5(config-if)#exit R5(config)#lldp run R5(config)#cdp enable R5#sh cdp neighbor R5#sh lldp neighbor
- D. R5(config)#int Gi0/1 R5(config-if)#no cdp enable R5(config-if)#exit R5(config)#no lldp run R5(config)#cdp run R5#sh cdp neighbor detail R5#sh lldp neighbor
Which two spanning-tree states are bypassed on an interface running PortFast? (Choose two.)
- A. disabled
- B. listening
- C. learning
- D. blocking
- E. forwarding
DRAG DROP –
Drag and drop the management connection types from the left onto the definitions on the right.
Select and Place:
