Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Which statement about Cisco Discovery Protocol is true?
A. It is a Cisco-proprietary protocol.
B. It runs on the network layer.
C. It can discover information from routers, firewalls, and switches.
D. It runs on the physical layer and the data link layer.
Refer to the exhibit. How will the router handle a packet destined for 192.0.2.156?
A. The router will forward the packet via either Serial0 or Serial1.
B. The router will return the packet to its source.
C. The router will forward the packet via Serial2.
D. The router will drop the packet.
Which technique can you use to route IPv6 traffic over an IPv4 infrastructure?
A. NAT
B. 6 to 4 tunneling
C. L2TPv3
D. dual-stack
Which statements describe the routing protocol OSPF? (Choose three.)
A. It supports VLSM.
B. It is used to route between autonomous systems.
C. It confines network instability to one area of the network.
D. It increases routing overhead on the network.
E. It allows extensive control of routing updates.
F. It is simpler to configure than RIP v2.
Refer to the exhibit. After you apply the given configurations to R1 and R2 you notice that OSPFv3 fails to start.
Which reason for the problem is most likely true ?
A. The area numbers on R1 and R2 are mismatched
B. The IPv6 network addresses on R1 and R2 are mismatched
C. The autonomous system numbers on R1 and R2 are mismatched
D. The router ids on R1 and R2 are mismatched
Which command is used to display the collection of OSPF link states?
A. show ip ospf link-state
B. show ip ospf lsa database
C. show ip ospf neighbors
D. show ip ospf database
Refer to the exhibit. A network associate has configured OSPF with the command:
City(config-router)# network 192.168.12.64 0.0.0.63 area 0
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)
A. FastEthernet0 /0
B. FastEthernet0 /1
C. Serial0/0
D. Serial0/1.102
E. Serial0/1.103
F. Serial0/1.104
Refer to the exhibit. C-router is to be used as a “router-on-a-stick” to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?
- A. These commands need to be added to the configuration: C-router(config)# router eigrp 123 C-router(config-router)# network 172.19.0.0
- B. These commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
- C. These commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172.19.0.0
- D. No further routing configuration is required.
Refer to the exhibit. Which address and mask combination represents a summary of the routes learned by EIGRP?
- A. 192.168.25.0 255.255.255.240
- B. 192.168.25.0 255.255.255.252
- C. 192.168.25.16 255.255.255.240
- D. 192.168.25.16 255.255.255.252
- E. 192.168.25.28 255.255.255.240
- F. 192.168.25.28 255.255.255.252
Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this router?
A. 10.1.1.2
B. 10.154.154.1
C. 172.16.5.1
D. 192.168.5.3