Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface?
A. the IP address of the first Fast Ethernet interface
B. the IP address of the console management interface
C. the highest IP address among its active interfaces
D. the lowest IP address among its active interfaces
E. the priority value until a loopback interface is configured
The OSPF Hello protocol performs which of the following tasks? (Choose two.)
A. It provides dynamic neighbor discovery.
B. It detects unreachable neighbors in 90 second intervals.
C. It maintains neighbor relationships.
D. It negotiates correctness parameters between neighboring interfaces.
E. It uses timers to elect the router with the fastest links as the designated router.
F. It broadcasts hello packets throughout the internetwork to discover all routers that are running OSPF.
Question 533
What are two requirements for an HSRP group? (Choose two.)
A. exactly one active router
B. one or more standby routers
C. one or more backup virtual routers
D. exactly one standby active router
E. exactly one backup virtual router
Which command can you enter to determine the addresses that have been assigned on a DHCP Server?
A. Show ip DHCP database.
B. Show ip DHCP pool.
C. Show ip DHCP binding.
D. Show ip DHCP server statistic.
On a corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?
A. a router with subinterfaces configured on the physical interface that is connected to the switch
B. a router with an IP address on the physical interface connected to the switch
C. a switch with an access link that is configured between the switches
D. a switch with a trunk link that is configured between the switches
Which IPv6 address block forwards packets to a multicast address rather than a unicast address?
A. 2000::/3
B. FC00::/7
C. FE80::/10
D. FF00::/12
What is the expected outcome when an EUI-64 address is generated?
A. The seventh bit of original MAC address of the interface is inverted
B. The interface ID is configured as a random 64-bit value
C. The characters FE80 are inserted at the beginning of the MAC address of the interface
D. The MAC address of the interface is used as the interface ID without modification
What is the difference regrading reliability and communication type between TCP and UDP?
A. TCP is reliable and is a connectionless protocol; UDP is not reliable and is a connection-oriented protocol.
B. TCP is not reliable and is a connectionless protocol; UDP is reliable and is a connection-oriented protocol.
C. TCP is reliable and is a connection-oriented protocol; UDP is not reliable and is a connectionless protocol.
D. TCP is not reliable and is a connection-oriented protocol; UDP is reliable and is a connectionless protocol.
Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?
A.
R1# config t
R1(config)# ip routing
R1(config)# ip route default-route 192.168.1.1
B.
R1# config t
R1(config)# ip routing
R1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.1
C.
R1# config t
R1(config)# ip routing
R1(config)# ip route 192.168.1.1 0.0.0.0 0.0.0.0
D.
R1# config t
R1(config)# ip routing
R1(config)# ip default-gateway 192.168.1.1
Which function dose the range of private IPv4 addresses perform?
A. allow multiple companies to each use the same address without conflicts
B. provides a direct connection for hosts from outside of the enterprise network
C. ensues that NAT is not required to reach the internet with private range addressing
D. enable secure communications to the internet for all external hosts