Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Refer to the exhibit. What two conclusions should be made about this configuration? (Choose two.)
A. The root port is FastEthernet 2/1
B. The designated port is FastEthernet 2/1
C. The spanning-tree mode is PVST+
D. This is a root bridge
E. The spanning-tree mode is Rapid PVST+
A network engineer must create a diagram of a multivendor network. Which command must be configured on the Cisco devices so that the topology of the network can be mapped?
A. Device(config)#lldp run
B. Device(config)#cdp run
C. Device(config-if)#cdp enable
D. Device(config)#flow-sampler-map topology
How do AAA operations compare regarding user identification, user services, and access control?
A. Authorization provides access control, and authentication tracks user services
B. Authentication identifies users, and accounting tracks user services
C. Accounting tracks user services, and authentication provides access control
D. Authorization identifies users, and authentication provides access control
What is difference between RADIUS and TACACS+?
A. RADIUS logs all commands that are entered by the administrator, but TACACS+ logs only start, stop, and interim commands.
B. TACACS+ separates authentication and authorization, and RADIUS merges them.
C. TACACS+ encrypts only password information, and RADIUS encrypts the entire payload.
D. RADIUS is most appropriate for dial authentication, but TACACS+ can be used for multiple types of authentication.
What is a difference between local AP mode and FlexConnect AP mode?
A. Local AP mode creates two CAPWAP tunnels per AP to the WLC
B. Local AP mode causes the AP to behave as if it were an autonomous AP
C. FlexConnect AP mode fails to function if the AP loses connectivity with the WLC
D. FlexConnect AP mode bridges the traffic from the AP to the WLC when local switching is configured
Refer to the exhibit. Which configuration issue is preventing the OSPF neighbor relationship from being established between the two routers?
A. R1 has an incorrect network command for interface Gi1/0.
B. R2 should have its network command in area 1.
C. R1 interface Gi1/0 has a larger MTU size.
D. R2 is using the passive-interface default command.
Refer to the exhibit. Router R1 is running three different routing protocols. Which route characteristic is used by the router to forward the packet that it receives for destination IP 172.16.32.1?
A. longest prefix
B. administrative distance
C. cost
D. metric
Refer to the exhibit. Router R1 Fa0/0 cannot ping router R3 Fa0/1. Which action must be taken in router R1 to help resolve the configuration issue?
A. set the default gateway as 20.20.20.2
B. configure a static route with Fa0/1 as the egress interface to reach the 20.20.2.0/24 network
C. configure a static route with 10.10.10.2 as the next hop to reach the 20.20.20.0/24 network
D. set the default network as 20.20.20.0/24
By default, how does EIGRP determine the metric of a route for the routing table?
A. It uses the bandwidth and delay values of the path to calculate the route metric.
B. It uses a default metric of 10 for all routes that are learned by the router.
C. It counts the number of hops between the receiving and destination routers and uses that value as the metric.
D. It uses a reference bandwidth and the actual bandwidth of the connected link to calculate the route metric.
A packet is destined for 10.10.1.22. Which static route does the router choose to forward the packet?
A. ip route 10.10.1.0 255.255.255.240 10.10.255.1
B. ip route 10.10.1.20 255.255.255.252 10.10.255.1
C. ip route 10.10.1.16 255.255.255.252 10.10.255.1
D. ip route 10.10.1.20 255.255.255.254 10.10.255.1