Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Refer to the exhibit. Which IPv6 configuration is required for R17 to successfully ping the WAN interface on R18?
A
B
C
D
Answer: B
Which type of organization should use a collapsed-core architecture?
A. large and requires a flexible, scalable network design
B. large and must minimize downtime when hardware fails
C. small and needs to reduce networking costs currently
D. small but is expected to grow dramatically in the near future
What is a capability of FTP in network management operations?
A. encrypts data before sending between data resources
B. devices are directly connected and use UDP to pass file information
C. uses separate control and data connections to move files between server and client
D. offers proprietary support at the session layer when transferring data
Refer to the exhibit. For security reasons, automatic neighbor discovery must be disabled on the R5 Gi0/1 interface.
These tasks must be completed:
– Disable all neighbor discovery methods on R5 interface Gi0/1.
– Permit neighbor discovery on R5’s interface Gi0/2.
– Verify there are no dynamically learned neighbors on R5 interface Gi0/1.
– Display the IP address of R6’s interface Gi0/2.
Which configuration must be used?
A.
R5(config)#int Gi0/1
R5(config-if)#no cdp enable
R5(config-if)#exit
R5(config)#lldp run
R5(config)#no cdp run
R5#sh cdp neighbor detail
R5#sh lldp neighbor
B.
R5(config)#int Gi0/1
R5(config-if)#no cdp enable
R5(config-if)#exit
R5(config)#no lldp run
R5(config)#cdp run
R5#sh cdp neighbor
R5#sh lldp neighbor
C.
R5(config)#int Gi0/1
R5(config-if)#no cdp run
R5(config-if)#exit
R5(config)#lldp run
R5(config)#cdp enable
R5#sh cdp neighbor
R5#sh lldp neighbor
D.
R5(config)#int Gi0/1
R5(config-if)#no cdp enable
R5(config-if)#exit
R5(config)#no lldp run
R5(config)#cdp run
R5#sh cdp neighbor detail
R5#sh lldp neighbor
What is a function of a Layer 3 switch?
A. move frames between endpoints limited to IP addresses
B. transmit broadcast traffic when operating in Layer 3 mode exclusively
C. forward Ethernet frames between VLANs using only MAC addresses
D. flood broadcast traffic within a VLAN
Which type of API allows SDN controllers to dynamically make changes to the network?
A. northbound API
B. REST API
C. SOAP API
D. southbound API
Drag and Drop Question
Drag and drop the lightweight access point operation modes from the left onto the descriptions on the right.
Which protocol is used in Software Defined Access (SDA) to provide a tunnel between two edge nodes in different fabrics?
A. Generic Router Encapsulation (GRE)
B. Virtual Local Area Network (VLAN)
C. Virtual Extensible LAN (VXLAN)
D. Point-to-Point Protocol (PPP)
Which plane is centralized by an SDN controller?
A. management-plane
B. data-plane
C. services-plane
D. control-plane
Refer to the exhibit. Which next-hop IP address does Router1 use for packets destined to host 10.10.13.158?
A. 10.10.10.5
B. 10.10.11.2
C. 10.10.12.2
D. 10.10.10.9