Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Refer to the exhibit. Users need to connect to the wireless network with IEEE 802. 11r-compatible devices. The connection must be maintained as users travel between floors or to other areas in the building. What must be the configuration of the connection?
A. Select the WPA Policy option with the CCKM option.
B. Disable AES encryption.
C. Enable Fast Transition and select the FT 802.1x option.
D. Enable Fast Transition and select the FT PSK option.
Refer to the exhibit. What is a reason for poor performance on the network interface?
A. The interface is receiving excessive broadcast traffic.
B. The cable connection between the two devices is faulty.
C. The interface is operating at a different speed than the connected device.
D. The bandwidth setting of the interface is misconfigured
Refer to the exhibit. A network engineer must update the configuration on Switch2 so that it sends LLDP packets every minute and the information sent via LLDP is refreshed every 3 minutes. Which configuration must the engineer apply?
A. Switch2(config)#lldp timer 60
Switch2(config)#lldp holdtime 180
B. Switch2(config)#lldp timer 60
Switch2(config)#lldp tlv-select 180
C. Switch2(config)#lldp timer 1
Switch2(config)#lldp holdtime 3
D. Switch2(config)#lldp timer 1
Switch2(config)#lldp tlv-select 3
Refer to the exhibit. Users on existing VLAN 100 can reach sites on the Internet. Which action must the administrator take to establish connectivity to the Internet for users in VLAN 200?
A. Define a NAT pool on the router.
B. Configure static NAT translations for VLAN 200.
C. Configure the ip nat outside command on another interface for VLAN 200.
D. Update the NAT_INSIDE_RANGES ACL.
Refer to the exhibit. Packets received by the router from BGP enter via a serial interface at 209.165.201.1. Each route is present within the routing table.
Which interface is used to forward traffic with a destination IP of 10.1.1.19?
A. F0/4
B. F0/0
C. F0/1
D. F0/3
Refer to the exhibit. An engineer is configuring an EtherChannel using LACP between Switches 1 and 2. Which configuration must be applied so that only Switch 1 sends LACP initiation packets?
A. Switch1(config-if)#channel-group 1 mode on
Swrtch2(config-if)#channel-group 1 mode passive
B. Switch1(config-if)#channel-group 1 mode passive
Switch2(config-if)#channel-group 1 mode active
C. Switch1(config-if)#channel-group 1 mode active
Switch2(config-if)#channel-group 1 mode passive
D. Switch1(config-if)#channel-group 1 mode on
Switch2(config-if)#channel-group 1 mode active
Refer to the exhibit. R1 learns all routes via OSPF. Which command configures a backup static route on R1 to reach the 192.168.20.0/24 network via R3?
A. R1(config)#ip route 192.168.20.0 255.255.0.0 192.168.30.2
B. R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2 90
C. R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2 111
D. R1(config)#ip route 192.168.20.0 255.255.255.0 192.168.30.2
What is the difference between IPv6 unicast and anycast addressing?
A. IPv6 anycast nodes must be explicitly configured to recognize the anycast address, but IPv6 unicast nodes require no special configuration
B. IPv6 unicast nodes must be explicitly configured to recognize the unicast address, but IPv6 anycast nodes require no special configuration
C. An individual IPv6 unicast address is supported on a single interface on one node but an IPv6 anycast address is assigned to a group of interfaces on multiple nodes.
D. Unlike an IPv6 anycast address, an IPv6 unicast address is assigned to a group of interfaces on multiple nodes
Refer to the exhibit. The router has been configured with a super net to accommodate the requirements for 380 users on a Subnet. The requirement already considers 30% future growth. Which configuration verifies the IP subnet on router R4?
A.
Subnet: 10.7.54.0
Subnet mask: 255.255.128.0
Broadcast address: 10.5.55.255
Usable IP address range: 10.7.54.1 – 10.7.55.254
B.
Subnet: 10.7.54.0
Subnet mask: 255.255.255.0
Broadcast address: 10.7.54.255
Usable IP address range: 10.7.54.1 – 10.7.55.254
C.
Subnet: 10.7.54.0
Subnet mask: 255.255.254.0
Broadcast address: 10.7.54.255
Usable IP address range: 10.7.54.1 – 10.7.55
D.
Subnet: 10.7.54.0
Subnet mask: 255.255.254.0
Broadcast address: 10.7.55.255
Usable IP address range: 10.7.54.1 – 10.7.55
A. SW1
B. SW2
C. SW3
D. SW4