Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Which authentication method requires the user to provide a physical attribute to authenticate successfully?
- A. biometric
- B. password
- C. multifactor
- D. certificate
Refer to the exhibit. An engineer is using the Cisco WLC GUI to configure a WLAN for WPA2 encryption with AES and preshared key Cisc0123456. After the engineer selects the WPA + WPA2 option from the Layer 2 Security drop-down list, which two tasks must they perform to complete the process? (Choose two.)
- A. Select CCKM from the Auth Key Mgmt drop-down list, set the PSK Format to Hex, and enter the key
- B. Select PSK from the Auth Key Mgmt drop-down list, set the PSK Format to ASCII, and enter the key.
- C. Select ASCII from the PSK Format drop-down list, enter the key, and leave the Auth Key Mgmt setting blank
- D. Select the WPA2 Policy and AES check boxes.
- E. Select the WPA2 Policy, AES, and TKIP check boxes
Which alternative to password authentication is implemented to allow enterprise devices to log in to the corporate network?
- A. 90-day renewal policies
- B. magic links
- C. one-time passwords
- D. digital certificates
Refer to the exhibit. Which switch in this configuration will be elected as the root bridge?
SW1: 0С:0А:05:22:05:97 –
SW2: 0C:0A:A8:1A:3C:9D –
SW3: 0С:0А:18:81:ВЗ:19 –
SW4: 0С:4А:82:56:35:78
- A. SW1
- B. SW2
- C. SW3
- D. SW4
Refer to the exhibit. What is the cause of poor performance on router R19?
- A. excessive collisions
- B. excessive CRC errors
- C. port oversubscription
- D. speed and duplex mismatch
Which protocol should be used to transfer large files on a company intranet that allows TCP 20 and 21 through the firewall?
- A. SMTP
- B. REST API
- C. TFTP
- D. FTP
Which Rapid PVST+ port state does a port operate in without receiving BPDUs from neighbors or updating the address database?
- A. listening
- B. forwarding
- C. disabled
- D. blocking
Refer to the exhibit. An engineer is creating a secure preshared key based SSID using WPA2 for a wireless network running on 2.4 GHz and 5 GHz. Which two tasks must the engineer perform to complete the process? (Choose two.)
- A. Select the 802.1x option for Auth Key Management
- B. Select the AES (CCMP128) option for WPA2 WPA3 Encryption
- C. Select the AES option for Auth Key Management
- D. Select the PSK option for Auth Key Management
- E. Select the WPA Policy option.
SIMULATION
–
Guidelines
–
This is a lab item in which tasks will be performed on virtual devices.
• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab doses and cannot be reopened.
Topology
Tasks
–
Refer to the topology. All physical cabling is in place. Routers 2 and 3 are inaccessible. Configure OSPF routing for the network and ensure R1 has joined Area 0 without using network statements.
Task 1
–
• Configure OSPF on R1 with a process ID and router- ID only as follows:
o use process ID 33
o use EO/1 IP as the router ID
Task 2
–
• Configure R1 to establish neighbor adjacencies with R2 and R3. The network statement under the OSPF process must not be used.
• Configure R1 to always become the DR for Area 0
Answer:
SIMULATION
–
Guidelines
–
This is a lab item in which tasks will be performed on virtual devices.
• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab doses and cannot be reopened.
Topology
–
Tasks
–
All physical cabling is in place and verified. Connectivity for the Switches on ports E0/1, E0/2, and E0/3 must be configured and available for voice and data capabilities.
1. Configure Sw1 and Sw2 with the VLAN naming as indicated.
2. Assign the VLANs to the appropriate interfaces and set a non-trunking, non-tagged, single-VLAN for each interface according to the topology.
3. Configure both switches to use the L2 vendor-neutral discovery protocol to broadcast device information, including the native VLAN across the e0/0 interfaces.
