CCNA 200-301 Exam Free Dumps | 100% Free, Complete & Latest Dumps with the Most Recent Updates

Pass CCNA 200-301 in Just 3 Days – Stress-Free!

Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!

Refer to the exhibit. Which switch in this configuration will be elected as the root bridge?

SW1 0С:0A:05:22:05:97 –

SW2 0С:4A:82:07:57:58 –

SW3 0C:0A:A8:1A:3C:9D –
SW4 0С:0A:18:A1:B3:19

Refer to the exhibit. Which configuration parameter is preventing host С from reaching the internet?

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary pre-configurations have been applied.
• Do not remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology
–

Tasks
–

Task 1
–

Configure trunks between Sw1 and Sw2 on ports E0/0 and E0/1 using the IEEE standard frame tagging method.

• Add VLAN 99 as untagged on the trunk ports.
• Only extend VLAN 110 and the untagged VLAN across the trunk.
• Verify that PC1 is capable of pinging PC2.

Task 2
–

On Sw1 and Sw2, use IEEE 802.3ad link aggregation.

• Combine E0/0 and E0/1 into a single logical link while leaving the trunk configurations intact.
• Assign number 20 to the link.
• Both links must negotiate aggregation.

Answer:

Refer to the exhibit. A network engineer is configuring a WLAN to use a WPA2 PSK and allow only specific clients to join. Which two actions must be taken to complete the process? (Choose two.)

What is the RFC 4627 default encoding for JSON text?

Refer to the exhibit. Which type of JSON data is represented?

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary pre-configurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology
–

Tasks
–

Refer to the topology. All physical cabling is in place. Configure local user account, configure a Named ACL (NACL), and Dynamic Arp Inspection.

1. Configure a local account on Sw3 with telnet access only on virtual ports 0-4. Use the following information:

– Username: tech12
– Password: load1key
– Algorithm type: md5
– Privilege level: Exec mode

2. Configure and apply a NACL on R1 to control network traffic towards ISP:

– Name: ISP_ACL
– Restrict RFC 1918 class A and B addresses
– Allow all other addresses

3. A DHCP IP Pool is preconfigured on R1 for VLAN 5, and DHCP Snooping is configured on Sw2. Configure on Sw2:

– Dynamic Arp Inspection for VLAN 5
– Enable validation of the ARP packet destination MAC address
– Enable validation of the ARP packet source MAC address
– Enable validation of the ARP Packet IP address

Answer:

A network engineer is configuring a new router at a branch office. The router is connected to an upstream WAN network that allows the branch to communicate with the head office. The central time server with IP address 172.24.54.8 is located behind a firewall at the head office. Which command must the engineer configure so that the software clock of the new router synchronizes with the time server?

Refer to the exhibit. All routers in the network are configured correctly, and the expected routes are being exchanged among the routers. Which set of routes are learned from neighbors and installed on router 2?