CCNA 200-301 Exam Free Dumps | 100% Free, Complete & Latest Dumps with the Most Recent Updates

Pass CCNA 200-301 in Just 3 Days – Stress-Free!

Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!

Refer to the exhibit. Which switch in this configuration will be elected as the root bridge?

Refer to the exhibit. Which switch in this configuration will be elected as the root bridge?

SW1: 0C:E4:82:33:62:23 –

SW2: 0C:0E:16:11:05:97 –

SW3: 0C:E0:16:1A:3C:9D –
SW4: 0C:00:18:A1:B3:19

Which two statements distinguish authentication from accounting? (Choose two.)

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary pre-configurations have been applied.
• Do not remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology
–

Tasks
–

Task 1
–

• Configure a host route on R5 for the destination of 10.200.220.6.
• Configure a static default route on R1 preferring the path through R3 towards R6.
• From R5, use traceroute and ping to verify the path towards and reachability of R6.

Task 2
–

• Configure a floating static default route on R1, preferring the path through R2 towards R6 if the link to R3 should fail.
• Configure the administrative distance for 225.
• Configure a static route on R2 to forward the return traffic towards 10.100.110.0/25.
• After shutting interface e0/1 on R1, use traceroute and ping from R5 to verify path towards and reachability of R6.

Answer:

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices:

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary pre-configurations have been applied.
• Do not remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology
–

Tasks
–

Reference Topology Diagram and table. Configure IPv4 and IPv6 between the two routers.

Task 1:

• Configure R1 with the first usable host IP address in the IPv4 network.
• Configure R2 with the last usable host IP address in the IPv4 network.
• Verify connectivity using ping.

Task 2:

• Do not assign the subnet router anycast address to either router.
• Configure R1 with the first usable host IP address in the IPv6 network.
• Configure R2 with the last usable host IP address in the IPv6 network.
• Verify connectivity using ping.

Answer:

Refer to the exhibit. Network services must be enabled on interface Gi1/0/34. Which configuration meets the needs for this implementation?

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology
–

Tasks
–

All physical cabling is in place and verified. Connectivity for PC1, PC2 and PC3 must be established to the switches. Each port connecting to the PCs must be configured as an end-user port and only allow the designated VLAN.

1. Configure VLAN 99 on all three switches and label it exactly as FINANCIAL
2. Configure the switch ports connecting to PC1, PC2 and PC3
3. Cisco’s neighbor discovery protocol has been disabled on SW-1 and must be re-enabled
4. PC1 must not be able to discover SW-1

Answer:

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.

Topology

Tasks
–

IP connectivity between the three routers is established. IP Services must be configured in the order presented to complete the implementation.

1. Configure dynamic one-to-one address mapping on R2 using a standard list named XLATE, which allows all traffic to translate the source address of R3 to a pool named test_pool using the 10.10.10.0/24 network for traffic sent from R3 to R1. Avoid using an NVI configuration. Verify reachability by sending a ping to 192.168.100.1 from R3.
2. Configure R3 to dynamically receive an IP address on Ethernet0/2 from the DHCP server.
3. Configure R1 as an NTP server and R2 as a client, not as a peer, using the IP address 10.1.2.1.
4. Configure SSH access from R1 to R3, while excluding access via other remote connection protocols using the user root and password s3cret on router R3 using RSA. Verify connectivity from router R1 to R3 using a destination address assigned to interface E0/2 on R3.

Refer to the exhibit. A secondary route is required on router R1 to pass traffic to the LAN network on R2 if the primary link fails. Which command must be entered to configure the router?