CCNA 200-301 Exam Free Dumps | 100% Free, Complete & Latest Dumps with the Most Recent Updates

Pass CCNA 200-301 in Just 3 Days – Stress-Free!

Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!

Refer to the exhibit. What is the metric for the route to the 192.168.10.33 host?

Refer to the exhibit. The IPv6 address for the LAN segment on router R2 must be configured using the EUI-64 format. When configured which ipv6 address is produced by the router?

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab doses and cannot be reopened.

Topology
–

Tasks
–

Refer to the topology. All physical cabling is in place. Configure a local user account, a Named ACL (NACL) and security.

1. Configure a local account on Sw101 with telnet access only on virtual ports 0-4. Use the following information:

– Username: netops
– Password: ipsec4all
– Algorithm: “Vigenere”
– Privilege level: Exec mode

2. Configure and apply a single NACL on Sw103 using the following:

– name: ENT_ACL
– Restrict only PC1 on VLAN 10 from pinging PC2
– Allow only PC1 on VLAN 10 to telnet to R1 (172.16.30.2)
– Prevent all other devices from telnetting from VLAN 10
– Allow all other network traffic from VLAN 10

3. Configure security on interface Ethernet 0/0 of Sw102:

– Set the maximum number of secure MAC addresses to two
– Ensure that the port discards the packet, counts the number of violations and sends a syslog message
– Allow secure mac addresses to be learned dynamically

Answer:

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab doses and cannot be reopened.

Topology
–

Tasks
–

SW-3 and SW-4 are preconfigured with all necessary commands. All physical cabling is in place and verified. All connectivity must be operational.

1. Configure both SW-1 and SW-2 switch ports e0/0 and e0/1 for 802.1q trunking with only VLANS 1, 12, and 22 permitted.
2. Configure SW-1 port e0/2 for 802.1q trunking and include only VLANS 12 and 22.
3. Configure both SW-1 and SW-2 switch ports e0/0 and e0/1 for link aggregation using the industry standard protocol. All ports must be configured so that they immediately negotiate the link.

Answer:

What are two reasons to implement DHCP in a network? (Choose two.)

SIMULATION
–

Guidelines
–

This is a lab item in which tasks will be performed on virtual devices

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.

Topology
–

Tasks
–

All physical cabling is in place and verified. Connectivity for the Switches on ports E0/1, E0/2, and E0/3 must be configured and available for voice and data capabilities.

1. Configure Sw1 and Sw2 with both VLANS, naming them according to the VLAN Name provided in the topology.
2. Configure the E0/1, E0/2, and E0/3 ports on both switches for both VLANS and ensure that Cisco IP phones and PCs pass traffic.
3. Configure Sw1 and Sw2 to allow neighbor discovery via the vendor-neutral protocol on e0/0.

Answer:

What is a characteristics of frame switching?

Refer to the exhibit. The IPv6 address for the LAN segment on router R2 must be configured using the EUI-64 format. When configured which ipv6 address is produced by the router?

SIMULATION
–

R1 has been pre-configured with all the necessary commands. All physical cabling is in place and verified. Connectivity to the end devices must be configured.

1. Configure SW-1 switch port 0/1 to carry traffic for the Cisco IP phone and PC
2. Configure SW-2 E0/1 to carry traffic for PC2
3. Configure VLAN 10 with the name “Engineering” on SW-1
4. Configure the link between SW-1 and SW-2 to use the vendor neutral neighbor discovery protocol
5. Configure the link on SW-1 to R1 so that it does not allow the Cisco neighbor discovery protocol to pass

Answer:

Refer to the exhibit. Which set of commands must be applied to the two switches to configure an LACP Layer 2 EtherChannel?