Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Refer to the exhibit. The IPv6 address for the LAN segment on router R2 must be configured using the EUI-64 format. When configured which ipv6 address is produced by the router?
- A. 2001:db8:d955:1697:1130:ABFF:FECC:1
- B. 2001:db8:d955:1697:4657:149F:FE65:1
- C. 2001:db8:d955:1697:11D8:BFFF:FE69:1
- D. 2001:db8:d955:1697:12D8:BAFE:FF01:1
SIMULATION
–
Guidelines
–
This is a lab item in which tasks will be performed on virtual devices.
• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology lab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
–
All physical cabling is in place and verified. Router R1 is configured and passing traffic for VLANs 5 and 6. All relevant ports are pre-configured as 802.1q trunks.
1. Configure SW-1 port E0/0 to permit only VLANS 5 and 6
2. Configure both SW-1 and SW-2’s E0/1 ports to send and receive untagged traffic over VLAN 77
3. Configure SW-2 E0/2 port to permit only VLAN 6
4. Configure both SW-3 and SW-4 ports e0/0 and e0/1 for link aggregation using the industry standard protocol with the following requirements:
– SW-3 ports must immediately negotiate the aggregation protocol
– SW-4 ports must not initiate the negotiation for the aggregation protocol
– Use the designated number assignment
Answer:
DRAG DROP
–
Drag and drop the characteristic from the left onto the cable type on the right.
What is represented by the word “switch” within this JSON schema?
- A. key
- B. object
- C. array
- D. value
What is a characteristic of private IPv4 addressing?
- A. reduces the forwarding table on network routers
- B. allows communication across external internet boundaries
- C. assigned by an enterprise organization to internal hosts
- D. complies with Payment Card industry regulations
Refer to the exhibit. The IPv6 address for the LAN segment on router R2 must be configured using the EUI-64 format. When configured which ipv6 address is produced by the router?
- A. 2001:db8:d945:91:12A0:AB34:FFCC:1
- B. 2001:db8:d945:91:11B0:ABFF:FECC:1
- C. 2001:db8:d945:91:4661:59FF:FF53:5
- D. 2001:db8:d945:91:1130:ABFF:FECC:1
What causes a port to be placed in the err-disabled state?
- A. shutdown command issued on the port
- B. port security violation
- C. nothing plugged into the port
- D. latency
What is a characteristic of private IPv4 addressing?
- A. used on the external interface of a firewall
- B. used by ISP’s when only one IP is needed to connect to the internet
- C. reduces the forwarding table on network routers
- D. address space which is isolated from the internet
Which physical component is distributed among multiple virtual machines running on the same hypervisor?
- A. external storage
- B. network interfaces
- C. backplane network
- D. hardware resources
DRAG DROP
–
Drag and drop the characteristic from the left onto the cable type on the right.
