Pass 300-710 SNCF in Just 3 Days – Stress-Free!
Get your 300-710 Securing Networks with Cisco Firepower certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Question 31
A hospital network needs to upgrade their Cisco FMC managed devices and needs to ensure that a disaster recovery process is in place. What must be done in order to minimize downtime on the network?
- A. Configure a second circuit to an ISP for added redundancy.
- B. Keep a copy of the current configuration to use as backup.
- C. Configure the Cisco FMCs for failover.
- D. Configure the Cisco FMC managed devices for clustering.
Correct Answer: D
Question 32
An organization has implemented Cisco Firepower without IPS capabilities and now wants to enable inspection for their traffic. They need to be able to detect protocol anomalies and utilize the Snort rule sets to detect malicious behavior. How is this accomplished?
- A. Modify the network discovery policy to detect new hosts to inspect.
- B. Modify the access control policy to redirect interesting traffic to the engine.
- C. Modify the intrusion policy to determine the minimum severity of an event to inspect.
- D. Modify the network analysis policy to process the packets for inspection.
Correct Answer: B
Question 33
An engineer is tasked with deploying an internal perimeter firewall that will support multiple DMZs. Each DMZ has a unique private IP subnet range. How is this requirement satisfied?
- A. Deploy the firewall in transparent mode with access control policies.
- B. Deploy the firewall in routed mode with access control policies.
- C. Deploy the firewall in routed mode with NAT configured.
- D. Deploy the firewall in transparent mode with NAT configured.
Correct Answer: B
Question 34
An engineer must configure high availability for the Cisco Firepower devices. The current network topology does not allow for two devices to pass traffic concurrently. How must the devices be implemented in this environment?
- A. Active/active mode
- B. Cluster span EtherChannel
- C. Active/passive mode
- D. Cluster interface mode
Correct Answer: C
Question 35
When deploying a Cisco ASA Firepower module, an organization wants to evaluate the contents of the traffic without affecting the network. It is currently configured to have more than one instance of the same device on the physical appliance. Which deployment mode meets the needs of the organization?
- A. Inline tap monitor-only mode
- B. Passive monitor-only mode
- C. Passive tap monitor-only mode
- D. Inline mode
Correct Answer: C
Question 36
An organization has a Cisco FTD that uses bridge groups to pass traffic from the inside interfaces to the outside interfaces. They are unable to gather information about neighboring Cisco devices or use multicast in their environment. What must be done to resolve this issue?
- A. Create a firewall rule to allow CDP traffic
- B. Create a bridge group with the firewall interfaces
- C. Change the firewall mode to transparent
- D. Change the firewall mode to routed
Correct Answer: C
Question 37
A network engineer implements a new Cisco Firepower device on the network to take advantage of its intrusion detection functionality. There is a requirement to analyze the traffic going across the device, alert on any malicious traffic, and appear as a bump in the wire. How should this be implemented?
- A. Specify the BVI IP address as the default gateway for connected devices
- B. Enable routing on the Cisco Firepower
- C. Add an IP address to the physical Cisco Firepower interfaces
- D. Configure a bridge group in transparent mode
Correct Answer: D
Question 38
Which two conditions must be met to enable high availability between two Cisco FTD devices? (Choose two.)
- A. Same flash memory size
- B. Same NTP configuration
- C. Same DHCP/PPoE configuration
- D. Same host name
- E. Same number of interfaces
Correct Answer: B, E
Question 39
An engineer is building a new access control policy using Cisco FMC. The policy must inspect a unique IPS policy as well as log rule matching. Which action must be taken to meet these requirements?
- A. Configure an IPS policy and enable per-rule logging
- B. Disable the default IPS policy and enable global logging
- C. Configure an IPS policy and enable global logging
- D. Disable the default IPS policy and enable per-rule logging
Correct Answer: C
Question 40
Which two OSPF routing features are configured in Cisco FMC and propagated to Cisco FTD? (Choose two.)
- A. OSPFv2 with IPv6 capabilities
- B. Virtual links
- C. SHA authentication to OSPF packets
- D. Area boundary router type 1 LSA filtering
Correct Answer: B, E