Pass CCNA 200-301 in Just 3 Days – Stress-Free!
Get your CCNA 200-301 certification with 100% pass guarantee. Pay only after passing!
Click here to secure your guaranteed certification now!
Have questions? Contact us directly on WhatsApp for quick support!
Refer to the exhibit. All switches are configured with the default STP priorities. During the STP elections, which switch becomes the root bridge if all interfaces are in the same VLAN?
- A. MDF-DC-1: 0d:E0:43:96:02:30
- B. MDF-DC-2: 0d:0E:18:1B:05:97
- C. MDF-DC-4: 0d:E0:19:A1:B3:19
- D. MDF-DC-3: 0d:0E:18:2A:3C:9D
What is a functionality of the control plane in the network?
- A. It looks up an egress interface in the forwarding information base.
- B. It forwards traffic to the next hop.
- C. It exchanges topology information with other routers.
- D. It provides CLI access to the network device.
Which 802.11 management frame type is sent when a client roams between access points on the same SSID?
- A. Reassociation Request
- B. Authentication Request
- C. Association Request
- D. Probe Request
What is the maximum number of concurrent Telnet sessions that a Cisco WLC supports?
- A. 3
- B. 5
- C. 6
- D. 15
What are two functions of a firewall within an enterprise? (Choose two.)
- A. It enables traffic filtering based on URLs.
- B. It serves as an endpoint for a site-to-site VPN in standalone mode.
- C. It provides support as an endpoint for a remote access VPN in multiple context mode.
- D. It offers Layer 2 services between hosts.
- E. It enables wireless devices to connect to the network.
Which command must be entered so that the default gateway is automatically distributed when DHCP is configured on a router?
- A. dns-server
- B. default-router
- C. ip helper-address
- D. default-gateway
Refer to the exhibit. A network engineer is verifying the settings on a new OSPF network. All OSPF configurations use the default values unless otherwise indicated. Which router does the engineer expect will be elected as the DR when all devices boot up simultaneously?
- A. R1
- B. R2
- C. R3
- D. R4
What describes the functionality of southbound APIs?
- A. They enable communication between the controller and the network device.
- B. They communicate with the management plane.
- C. They use HTTP messages to communicate.
- D. They convey information from the controller to the SDN applications.
SIMULATION
–
Guidelines
–
This is a lab item in which tasks will be performed on virtual devices
• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked the lab closes and cannot be reopened.
Topology
Tasks
–
IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1:
1. Configure reachability to the switch SW1 LAN subnet in router R2.
2. Configure default reachability to the Internet subnet in router R1.
3. Configure a single static route in router R2 to reach to the Internet subnet considering both redundant links between routers R1 and R2. A default route is NOT allowed in router R2.
4. Configure a static route in router R1 toward the switch SW1 LAN subnet where the primary link must be through Ethernet0/1, and the backup link must be through Ethernet0/2 using a floating route. Use the minimal administrative distance value when required.
Answer:
Which two types of attack are categorized as social engineering? (Choose two.)
- A. phoning
- B. malvertising
- C. probing
- D. pharming
- E. phishing